UHBR13.5 vs UHBR20: max refresh rate at 4K and 1440p
4K at 240 Hz in 10-bit colour needs about 68.6 Gbps. UHBR20 carries 77.37, so it runs uncompressed. UHBR13.5 carries about 52.22, so it needs DSC. Seven modes at two bit depths against all three DisplayPort 2.1 speeds, with the pixel clock behind every row.
UHBR20 is the only DisplayPort 2.1 speed that runs 4K at 240 Hz in 10-bit colour without DSC. That mode needs about 68.6 Gbps. UHBR20 carries 77.37 Gbps of picture data, UHBR13.5 about 52.22 and UHBR10 about 38.69. So on UHBR13.5, the speed of AMD's RX 7000 and RX 9070 cards, 4K 240 Hz needs DSC. At 1440p, UHBR13.5 runs 360 Hz uncompressed even at 10-bit, while 480 Hz needs UHBR20 or DSC. 4K at 480 Hz needs DSC on every speed, UHBR20 included.
What UHBR10, UHBR13.5 and UHBR20 mean
UHBR stands for Ultra High Bit Rate. It is the name for the fast link rates added in DisplayPort 2.x. The number is the speed of one lane in Gbps (gigabits per second). A DisplayPort cable has four lanes, four data paths side by side. So UHBR20 is 20 Gbps a lane, or 80 Gbps raw.
VESA's DisplayPort 2.1 release (October 17, 2022) names the "UHBR10 link rate (10 Gbps)" and the "UHBR20 link rate (20 Gbps)". The middle speed came in writing later. VESA's DisplayPort 2.1a announcement (January 8, 2024) gives four-lane UHBR13.5 "a maximum throughput of 54 Gbps".
Not all of that is picture. DisplayPort.org says DisplayPort 2.1 uses "more efficient 128b/132b channel coding, delivering a maximum payload of 77.37 Gbps" at UHBR20. The payload is what is left for the image. We scale that stated figure by lane speed for the other two:
The pixel clock is how many pixels the link sends per second. It counts the visible pixels plus blanking, the unseen gap a video signal leaves around each line and each frame.
When a mode's data rate is bigger than the payload, it needs DSC. DSC (Display Stream Compression) is VESA's compression standard. VESA says it can cut the bandwidth "in excess of 67 percent without visual artifacts". DisplayPort.org gives its typical ratio as "1:1 to about 3:1".
Every mode against the three UHBR speeds
We worked out pixel clocks with an open implementation of VESA's CVT 1.2 timing formula, in reduced blanking v2 mode. These are the same clocks as our DisplayPort 1.4 page.
| Mode | Pixel clock (MHz) | 8-bit (Gbps) | 10-bit (Gbps) | No DSC at 8-bit | No DSC at 10-bit |
|---|---|---|---|---|---|
| 4K 144 Hz | 1306.2 | 31.35 | 39.19 | All three | UHBR13.5, UHBR20 |
| 4K 165 Hz | 1512.2 | 36.29 | 45.37 | All three | UHBR13.5, UHBR20 |
| 4K 240 Hz | 2285.2 | 54.84 | 68.56 | UHBR20 only | UHBR20 only |
| 4K 480 Hz | 5217.7 | 125.22 | 156.53 | None | None |
| 1440p 360 Hz | 1640.4 | 39.37 | 49.21 | UHBR13.5, UHBR20 | UHBR13.5, UHBR20 |
| 1440p 480 Hz | 2343.1 | 56.23 | 70.29 | UHBR20 only | UHBR20 only |
| 1440p 540 Hz | 2731.4 | 65.55 | 81.94 | UHBR20 only | None |
Turned around, this gives the top refresh at each resolution. We stepped the refresh up one hertz at a time until the data rate passed each payload:
| Resolution | DP 1.4 (Hz) | UHBR10 (Hz) | UHBR13.5 (Hz) | UHBR20 (Hz) |
|---|---|---|---|---|
| 1920 x 1080 | 406 / 337 | 555 / 468 | 688 / 587 | 884 / 770 |
| 2560 x 1440 | 251 / 205 | 354 / 293 | 452 / 378 | 609 / 516 |
| 3440 x 1440 | 193 / 158 | 277 / 227 | 358 / 296 | 491 / 412 |
| 3840 x 2160 | 120 / 97 | 174 / 142 | 229 / 187 | 323 / 267 |
The close calls, and which way they go
Some rows miss by only a few percent. Real monitors use their own timings, so those rows can go either way. One test settles most of them: count the visible pixels alone, with no blanking at all. If that is still more than the payload, no timing can fit, and DSC is certain.
- 4K 240 Hz, 10-bit, on UHBR13.5: visible pixels alone are 3840 x 2160 x 240 x 30 = 59.72 Gbps. That is more than 52.22, so DSC is certain.
- 4K 240 Hz, 8-bit, on UHBR13.5: 54.84 Gbps at CVT timing, 5% over. Visible pixels alone are 47.78, which fits. So only a monitor with much shorter blanking avoids DSC.
- 1440p 480 Hz, 8-bit, on UHBR13.5: 7.7% over at CVT timing. Visible pixels alone are 42.47.
- 1440p 540 Hz, 10-bit, on UHBR20: 5.9% over. Visible pixels alone are 59.72.
- UHBR10: 1440p 360 Hz at 8-bit misses by 1.8%, and 4K 144 Hz at 10-bit by 1.3%.
4K at 480 Hz is not close on any speed. At 8-bit its visible pixels alone come to 95.55 Gbps, more than UHBR20's 77.37.
Worked case: one 4K 240 Hz monitor, two graphics cards
Take MSI's MPG 322URX QD-OLED. MSI's datasheet lists "1x DisplayPort 2.1a (UHBR20)" and "DisplayPort: 3840 x 2160 (Up to 240Hz)". It gives the panel as "1.07B, 10 bits". So the mode to carry is 4K 240 Hz at 10-bit: 68.56 Gbps.
First, plug it into a GeForce RTX 5070. NVIDIA's spec page lists "DisplayPort 2.1b with UHBR20". Both ends run UHBR20, so the link carries 77.37 Gbps. 68.56 is 89% of that. The mode fits with 11% to spare, and no DSC is needed.
Now swap in a Radeon RX 9070 XT. AMD's product page says only "DisplayPort 2.1a" and gives no rate. KitGuru's review of ASRock's RX 9070 XT Taichi says its DisplayPort 2.1 outputs "are UHBR13.5 bandwidth, not the full UHBR20 spec". Club386 lists the whole series as "DP 2.1a UHBR13.5".
A link runs at the speed of its slower end. So this pair gets UHBR13.5, or 52.22 Gbps. 68.56 / 52.22 is about 1.31, so the card needs DSC at roughly 1.3:1. That is well inside the "1:1 to about 3:1" DisplayPort.org calls typical. The monitor still runs 4K 240 Hz on both cards. Only the RTX 5070 runs it uncompressed. For that link the cable has to carry UHBR20 too (which DisplayPort cable covers DP80).
"DisplayPort 2.1 means no DSC" is the wrong half
Two claims circulate. One says a DisplayPort 2.1 port runs 4K 240 Hz uncompressed. The other says only UHBR20 does. The second is right.
TFTCentral reports that LG confirmed its 32GX870A runs DisplayPort 2.1 at UHBR13.5 only, so it "will still need DSC to power the spec". It adds: "Only a full UHBR20 DP 2.1 connection could handle 4K 240Hz without DSC." The table agrees. At 10-bit no timing fits UHBR13.5, and at 8-bit CVT timing misses by 5%.
The first claim persists because the version number hides the speed. DisplayPort.org says DP 2.1b certification needs "HBR2 data rate at a minimum" plus DSC, and at least one item from a list. UHBR is one item on that list, not a must. HBR2 is a DisplayPort 1.2 speed. So "DP 2.1" on a box tells you nothing about the rate. Look for UHBR13.5 or UHBR20 written out, as MSI's sheet does.
NVIDIA's own wording shows the other edge. Its RTX 50 page says "up to 4K 480Hz or 8K 165Hz with DSC". 4K 480 Hz needs about 1.6:1 at 8-bit and 2:1 at 10-bit, even on UHBR20.
Where this stops applying
Every figure assumes CVT reduced blanking v2, full RGB colour and four lanes. Monitors ship their own timings, so the close calls above can land either way. The link is only as fast as the slowest of card, monitor and cable, and the monitor's menu can set a lower DisplayPort version. 4:2:2 colour, 12-bit and USB-C links are not covered here (USB-C max refresh rate covers that last one). DSC is not free on NVIDIA cards: when the card drives a mode with more than one internal head, DSR, DLDSR and Image Scaling turn off, as our DSC article explains. The worked case is arithmetic on published specs, not a test of the MSI monitor or either card.
UHBR speeds in five lines
- Payload: UHBR10 38.69, UHBR13.5 52.22, UHBR20 77.37 Gbps (UHBR20 stated by DisplayPort.org, the other two scaled from it).
- 4K 240 Hz needs 54.84 Gbps at 8-bit and 68.56 at 10-bit. Only UHBR20 carries it without DSC.
- 1440p 360 Hz fits UHBR13.5 uncompressed at 10-bit. 1440p 480 Hz needs UHBR20 or DSC.
- 4K 480 Hz needs DSC on every speed, UHBR20 included.
- RTX 50 = UHBR20 (NVIDIA). RX 9070 = UHBR13.5 (KitGuru, Club386; AMD's page gives no rate). The link runs at the slower end.
Sources
- VESA, VESA Releases DisplayPort 2.1 Specification, October 17, 2022 (UHBR10 and UHBR20 lane rates, DSC "in excess of 67 percent").
- VESA, DisplayPort 2.1a announcement, January 8, 2024 (four-lane UHBR13.5, 54 Gbps).
- DisplayPort.org, FAQ (128b/132b coding, 77.37 Gbps UHBR20 payload, DSC typical ratio, DP 2.1b certification minimum).
- kevinlekiller, CVT 1.2 modeline calculator (reduced blanking v2 timings, run for every mode here).
- NVIDIA, GeForce RTX 5070 family specifications (DisplayPort 2.1b with UHBR20, 4K 480 Hz with DSC).
- AMD, Radeon RX 9070 XT specifications (DisplayPort 2.1a, no rate stated).
- Dominic Moass, KitGuru, AMD RX 9070 XT review ft. ASRock, March 5, 2025 (UHBR13.5 outputs).
- Fahd Temsamani, Club386, AMD confirms Radeon RX 9070 series specs, February 27, 2025 (DP 2.1a UHBR13.5, no UHBR20).
- MSI, MPG 322URX QD-OLED datasheet (DisplayPort 2.1a UHBR20, 4K up to 240 Hz, 10-bit panel).
- TFTCentral, LG 32GX870A launched with DisplayPort 2.1 UHBR13.5, April 17, 2025.
Frequently asked questions
Does 4K 240 Hz need UHBR20?
At 10-bit colour, yes, if you want it without DSC. The mode needs about 68.56 Gbps at standard reduced blanking, and UHBR20 carries 77.37. UHBR13.5 carries about 52.22, and even the visible pixels alone come to 59.72 Gbps. At 8-bit the mode needs 54.84 Gbps, 5% more than UHBR13.5, so it still needs DSC unless the monitor uses unusually short blanking.
Can UHBR13.5 do 1440p 360 Hz without DSC?
Yes, at 8-bit and at 10-bit. 1440p 360 Hz needs 39.37 Gbps at 8-bit and 49.21 Gbps at 10-bit. UHBR13.5 carries about 52.22, so even 10-bit has about 6% to spare.
Does 4K 480 Hz need DSC on UHBR20?
Yes. It needs about 125 Gbps at 8-bit, and the visible pixels alone come to 95.55 Gbps, more than the 77.37 UHBR20 carries. NVIDIA's own RTX 50 spec says "up to 4K 480Hz or 8K 165Hz with DSC". DSC at about 1.6:1 (8-bit) or 2:1 (10-bit) brings it inside the link.
Is UHBR13.5 52.22 or 52.36 Gbps?
52.36 is 54 Gbps times the 128b/132b coding alone. DisplayPort.org states 77.37 Gbps for UHBR20, a little under the 77.58 the same sum gives, so we scale its stated figure: 77.37 x 13.5 / 20 = 52.22. The 0.3% gap does not move any mode on this page from fits to does not fit.
Do AMD RX 9070 cards support UHBR20?
No. AMD's product page says only "DisplayPort 2.1a". KitGuru's review of an RX 9070 XT says its DisplayPort 2.1 outputs "are UHBR13.5 bandwidth, not the full UHBR20 spec", and Club386 lists the series as "DP 2.1a UHBR13.5". NVIDIA lists RTX 50 cards as "DisplayPort 2.1b with UHBR20".