Gear GeeksGaming

Can you daisy chain two 1440p 144 Hz monitors over DisplayPort?

Not without compression. Two 1440p 144 Hz screens need about 28 Gbps between them, and DisplayPort 1.4 carries 25.92. A DP 1.4 daisy chain runs two 1440p screens at up to 128 Hz uncompressed. Every pair from 1080p to 4K, worked out with the DisplayPort standard's own sharing rules.

MonitorsUpdated 7 min read

No, not uncompressed. Two 1440p 144 Hz monitors need 28.16 Gbps at 8-bit colour, and DisplayPort 1.4 carries 25.92 Gbps for everything on the cable. Daisy chained on DP 1.4, two 1440p screens top out at 128 Hz without compression. 144 Hz, 165 Hz and 240 Hz pairs only run with DSC. On DisplayPort 1.2, which has no DSC, a 1440p pair stops at 87 Hz. A 1440p gaming screen plus a 1080p 60 Hz side screen does fit DP 1.4, up to 165 Hz on the main screen.

What a daisy chain is, and why it halves the bandwidth

A daisy chain runs one cable from the graphics card to the first monitor, and a second cable from that monitor to the next one. The feature that makes it work is MST, short for Multi-Stream Transport. MST lets one DisplayPort link carry several separate video streams, one per screen. The first monitor keeps its own stream and passes the other one on.

The catch is the first cable. Both pictures travel down it together, so they share one link's payload, the data rate left for pictures. VESA's 2019 USB DevDays slides give the formula: lane rate, times 0.8 for encoding, times four lanes. That is 25.92 Gbps for DisplayPort 1.4 (HBR3) and 17.28 Gbps for DisplayPort 1.2 (HBR2).

MST then takes a small cut of its own. It splits the link into 64 time slots, and each stream gets a whole number of them. The rules below come from the Linux kernel's DisplayPort MST code, which implements the DisplayPort standard and cites its sections. On DP 1.2 and DP 1.4 links it reserves the first slot and hands out the other 63. It rounds each stream up to whole slots. And it adds a 0.6% margin to each stream, which the kernel's helper code labels "SSC downspread and ref clock variation margin" from DP Standard v2.1, section 2.6.4.1.

slot size = payload / 64 (DP 1.4: 0.405 Gbps, DP 1.2: 0.27 Gbps) usable slots = 63 slots per screen = data rate x 1.006 / slot size, rounded up data rate = pixel clock x 24 (8-bit) or x 30 (10-bit) a pair fits if its two slot counts add up to 63 or less

The pixel clock is how many pixels per second a mode sends, counting the visible picture and the unseen blanking around it. We use CVT reduced blanking v2 clocks from an open CVT 1.2 calculator, the same clocks as our DisplayPort 1.4 page.

Worked case: two 1440p 144 Hz monitors on a DP 1.4 card

Take two 1440p 144 Hz monitors and a graphics card with DisplayPort 1.4. Each screen at 144 Hz has a 586.59 MHz pixel clock. At 8-bit that is 14.08 Gbps. Add the 0.6% margin and divide by the 0.405 Gbps slot, and you get 34.97, so each screen needs 35 slots. The pair needs 70. The link has 63. It does not fit.

The margin is not what sinks it. Without any MST cut, the pair still needs 28.16 Gbps against 25.92. So no timing trick rescues this pair uncompressed.

Drop both screens to 120 Hz and each needs 29 slots, 58 in all, which fits. The highest refresh that fits for an identical pair is 128 Hz. Or keep one screen fast. A 1440p 144 Hz main screen takes 35 slots and a 1080p 60 Hz side screen takes 8, so 43 are used. Even a 1440p 165 Hz main screen fits beside the 1080p 60 Hz one, at 41 plus 8. If both screens must run at 144 Hz, you have two choices: DSC on both, or two cables from two ports on the card.

Every pair on DP 1.2 and DP 1.4

Each row is two identical screens on one chain. "Fits" shows the slots used out of 63. On DP 1.4, a pair that misses can still run with DSC (Display Stream Compression), if every device in the chain supports it. The figure in brackets is the rough compression the pair needs: its data rate with the margin, against 63 slots. DisplayPort.org gives DSC's typical ratio as "1:1 to about 3:1". So a pair that needs more than 3:1 is marked no. DP 1.2 has no DSC.

Two identical screens on one DisplayPort link with MST, derived at CVT reduced blanking v2, full RGB colour.
Each screenPer screen, 8-bit (Gbps)DP 1.2, 8-bitDP 1.2, 10-bitDP 1.4, 8-bitDP 1.4, 10-bit
1080p 60 Hz3.20Fits (24)Fits (30)Fits (16)Fits (20)
1080p 120 Hz6.59Fits (50)Fits (62)Fits (34)Fits (42)
1080p 144 Hz8.00Fits (60)NoFits (40)Fits (50)
1080p 165 Hz9.26NoNoFits (46)Fits (58)
1080p 240 Hz14.00NoNoDSC (1.1:1)DSC (1.4:1)
1440p 60 Hz5.63Fits (42)Fits (54)Fits (28)Fits (36)
1440p 120 Hz11.59NoNoFits (58)DSC (1.1:1)
1440p 144 Hz14.08NoNoDSC (1.1:1)DSC (1.4:1)
1440p 165 Hz16.30NoNoDSC (1.3:1)DSC (1.6:1)
1440p 240 Hz24.62NoNoDSC (1.9:1)DSC (2.4:1)
3440x1440 60 Hz7.51Fits (56)NoFits (38)Fits (48)
3440x1440 120 Hz15.46NoNoDSC (1.2:1)DSC (1.5:1)
3440x1440 144 Hz18.77NoNoDSC (1.5:1)DSC (1.9:1)
3440x1440 165 Hz21.73NoNoDSC (1.7:1)DSC (2.1:1)
3440x1440 240 Hz32.83NoNoDSC (2.6:1)No (3.2:1)
4K 60 Hz12.54NoNoOne slot short (64)DSC (1.2:1)
4K 120 Hz25.82NoNoDSC (2.0:1)DSC (2.5:1)
4K 144 Hz31.35NoNoDSC (2.5:1)No (3.1:1)
4K 165 Hz36.29NoNoDSC (2.9:1)No (3.6:1)
4K 240 Hz54.84NoNoNo (4.3:1)No (5.4:1)

Turned around, this gives the top refresh for an identical pair. We stepped the refresh up one hertz at a time until each screen needed more than 31 slots:

Highest whole refresh rate for two identical screens on one MST link without DSC, derived at CVT reduced blanking v2.
Each screenDP 1.2, 8-bit (Hz)DP 1.2, 10-bit (Hz)DP 1.4, 8-bit (Hz)DP 1.4, 10-bit (Hz)
1920 x 1080149121216176
2560 x 14408770128104
3440 x 144066539779
3840 x 216040325948

If you ignore the MST cut and just halve the link, only one row changes: two 4K 60 Hz screens at 8-bit. They need 25.08 Gbps against 25.92, so a plain halving says they fit. With the slot rules each screen needs 32 slots, so the pair needs 64 of 63. That row sits right on the edge, and the monitor's own timing decides it.

"Often too much": the vague answer, and where the edge sits

Most answers to this question stop at "it depends on bandwidth". KTC's guide gives a planning baseline: DP 1.2 carries "four 1080p displays or two 2560 x 1600 displays", and DP 1.3/1.4 "two 4K displays at 60 Hz". The 1080p and 1440p figures agree with the table. The 4K 60 Hz pair is the one-slot case above, so it is the claim to check against your monitor's spec sheet.

EIZO's guide says "the bandwidth of DisplayPort 1.2 is 21.6 Gbps". That is the raw rate. After encoding, 17.28 Gbps is left for pictures, and only that figure tells you what fits. EIZO's own table, at 60 Hz, allows two 1440p screens or one 4K screen on DP 1.2. That matches the arithmetic here.

BenQ writes: "We don’t recommend this setup for gaming as it introduces greater latency." It gives no figure, and we found no measurement. The cost a daisy chain certainly carries is bandwidth, which is what caps both screens.

What the card and monitors must support

The arithmetic only matters once the chain works at all. Dell's daisy chain guide sets the rules. The card needs DisplayPort 1.2 or newer. The first monitor needs a DisplayPort In and a DisplayPort Out, and must support MST. The monitors after it do not need MST. HDMI cannot daisy chain at all.

MST is often off out of the box. Dell says that "by default, this feature is not enabled on Dell monitors", and it must be switched on in the monitor's menu. The last monitor is the reverse. In a Dell note on Intel HD Graphics, the last screen must have DP 1.2 (MST) turned off, because the Intel driver needs it as a "terminator" to end the chain. On older monitors where MST is a "DP 1.2" menu setting, the first link runs at HBR2, so the DP 1.2 columns apply. Our DisplayPort 1.2 page covers that setting.

The card limits the count too. EIZO lists four screens over DP 1.2 MST for GeForce 900 series or later and Radeon 400 series, and three for Intel UHD 600 series. Macs are the big exception. EIZO says macOS does not support DisplayPort MST. Plugable says Apple Silicon Macs (M1, M2, M3) mirror one picture on both screens of an MST dock. The same page shows DSC working over MST: a Windows laptop with HBR3 and DSC "can support up to two 4K 120Hz displays", a pair the table puts at about 2:1.

Where this stops applying

Every figure assumes CVT reduced blanking v2, full RGB colour and four lanes. Monitors ship their own timings, so the edge cases can go either way: two 4K 60 Hz screens, and 1080p 120 Hz at 10-bit on DP 1.2 (62 of 63). The slot rules are read from the Linux implementation of the standard. Windows drivers do not publish theirs. The DSC ratios are rough, and they only help if the card and the first monitor both support DSC over MST. Plugable notes that HBR3 and DSC are "not required to be implemented" on every USB4 or Thunderbolt 4 laptop. A chain is as fast as its slowest link, so a DP 1.4 card with a DP 1.2 first monitor is a DP 1.2 chain. USB-C often carries DisplayPort on two lanes, which halves everything here (USB-C max refresh rate). Variable refresh over MST is not covered. This is arithmetic, not a test of any monitor or card.

Two screens on one DisplayPort cable

  • Both screens share one link: 25.92 Gbps on DP 1.4, 17.28 on DP 1.2. MST uses 63 of 64 time slots, whole slots per screen, plus 0.6%.
  • Two 1440p 144 Hz screens need 70 slots on DP 1.4. They do not fit uncompressed. The top for a 1440p pair is 128 Hz (DP 1.4) or 87 Hz (DP 1.2).
  • A 1440p 144 or 165 Hz main screen plus a 1080p 60 Hz side screen fits DP 1.4.
  • Pairs past that need DSC on DP 1.4, with support in the card and the first monitor. See what DSC costs.
  • First monitor: DP Out, MST on. Last monitor: MST off, which Intel graphics needs to end the chain. No MST on macOS.

Sources

Frequently asked questions

Can DisplayPort 1.4 run two 1440p 144 Hz monitors in a daisy chain?

Only with DSC. Each 1440p 144 Hz screen needs 14.08 Gbps at 8-bit colour, so the pair needs 28.16 Gbps. DisplayPort 1.4 carries 25.92 Gbps in total, before MST takes its share. Uncompressed, a DP 1.4 chain tops out at two 1440p screens at 128 Hz.

Can DisplayPort 1.2 daisy chain two 1440p monitors at 144 Hz?

No. DP 1.2 carries 17.28 Gbps and has no DSC. Two 1440p screens fit at 60 Hz, and the top for a pair is 87 Hz at 8-bit. One 1440p 144 Hz screen alone uses most of a DP 1.2 link.

Can I daisy chain a 1440p 165 Hz gaming monitor and a 1080p 60 Hz second screen?

On DisplayPort 1.4, yes, at 8-bit. The 165 Hz screen takes 41 of the link's 63 time slots and the 1080p 60 Hz screen takes 8, so 49 are used. A 1440p 240 Hz main screen does not leave room: it takes 62 slots on its own.

Does daisy chaining add input lag?

We found no measurement. BenQ writes: "We don’t recommend this setup for gaming as it introduces greater latency." It gives no figure and no test. What a daisy chain does cost for certain is bandwidth, which caps the refresh rate of both screens.

Can a Mac daisy chain two monitors over DisplayPort?

Not as two separate desktops. EIZO says macOS does not support DisplayPort MST. Plugable says Apple Silicon Macs (M1, M2, M3) mirror the same picture on both screens of an MST dock. Dell lists DisplayPort daisy chains on macOS as duplicate mode only.

Sourcing. Link rates and the 25.92 Gbps usable-rate formula are from VESA's USB DevDays 2019 presentation. The MST sharing rules (63 usable time slots of 64 on 8b/10b links, whole slots per stream, a 0.6% margin from DP Standard v2.1 section 2.6.4.1) are read from the Linux kernel's DisplayPort MST and helper code, which implements the standard and cites its sections. Pixel clocks are derived with kevinlekiller's open CVT 1.2 calculator in reduced blanking v2 mode, the same clocks as our DisplayPort 1.2 and 1.4 pages. Hardware conditions are manufacturer-stated, from Dell, EIZO and Plugable. The DSC typical ratio is from DisplayPort.org's FAQ. BenQ and KTC are quoted as the claims being tested. Checked November 20, 2026. Found an error? Send a correction.